Catalyst

The Catalyst® alarm system monitors up to 256 registers, providing real-time alerts for up to 96 destinations. It's the reliable, adaptable solution.

• Integrating the Catalyst and Cellularm
• Resetting my Catalyst to factory default settings
• Catalyst Alarmware cable is required for connecting the USB with Catalyst
• Total Output Capacity of the Catalyst
• Over The Phone Session: Enter program mode
• Dimensions of the Cellularm NEMA 4X enclosure
• Data Types Saved to the Catalyst Log File
• PLC communication failures
• Outgoing Call Answer Limit
• Retrieving Catalyst Data
• Alarmware: Catalyst's Configuration Software
• Catalyst Memory Allocation and Management
• Interfacing the Catalyst and Automation Direct Terminator I/O
• Report Delivery Rules
• TFAIL (Telephone Line Fault Detection)
• Determining Recording Time Available
• Over the Phone (OTP) Menu Options
• Catalyst MB+ Support
• Log File Name and Folder
• Acknowledging all the alarms without listening to all alarm reports
• Electrical Power Requirements for the Catalyst
• Dimensions of the Catalyst NEMA 4X enclosure
• Diagnostics and Self-Tests available for the Catalyst
• First Channel Setting Configured: SNA
• Configuring the Number of Rings the Catalyst will Wait to Answer an Incoming Call
• USB Ports and Connecting to the Catalyst
• When is Log File Data deleted?
• Copy one Catalyst Configuration to another Catalyst Configuration
• Alarmware Idle Timeout
• Disarming and Arming the Catalyst Based on Time-of-Day (Shift)
• Making programming changes to the Catalyst from different location
• What if the Catalyst is disarmed?
• Catalyst - PA feature via its PNP Transistor output during a TFAIL
• Calculating the amount of memory to reserve for Log File data
• Catalyst Protocol Information
• Alarmware off-site configuration - possible?
• Catalyst - Using PA as a calling destination
• Catalyst Report Types
• Catalyst Destination Types
• How do I find Catalyst hardware and Alarmware software version information?
• Channel or destination copy to/from operations
• Installing Flash Memory
• Do RACO Products need Material Safety Data Sheets (MSDS)?
• Troubleshooting phone line problems
• Catalyst Channel States
• VERBATIM & CATALYST CHANGE TO BUL IN-LINE POWER SUPPLY
• Disabled Phone Line
• I am not able to acknowledge alarms from my cellphone
• Does my Verbatim battery need replacing?
• Catalyst Communications Connection
• Existing Catalyst log file data when changes are made to the configuration
• Scaling Catalyst Raw Data Values
• Using the Catalyst and/or Alarmware to Read and Write Values To and From the PLC?
• Connecting Catalyst to Automation Direct Terminator IO Modbus Cable
• Catalyst Cable Drawings
• Catalyst Redial Attempts and time between calls (Intersession Delay)
• Determining Catalyst Firmware Version
• Catalyst - Physical Ouput or Virtual Output via PLC
• Log File Data Format
• Catalyst has Called All the Destinations Enabled to Receive Alarm Calls
• Where can I download the Alarmware Software
• Log File "filename" extension
• Connecting Catalyst Cable to Bristol Babcock Modbus Cable 3335 and newer 3330/3550 CAT-BB9
• How do I integrate Micrologix to Catalyst via Modbus Protocol over RS232?
• Catalyst Owner's Manual Version 1.87
• Catalyst Ethernet Option Setup - Version 5 VO3
• RSLogix 5000 Configuration for both the Verbatim Gateway and Catalyst Autodialer EtherNet Options
• Ethernet/IP option for the Catalyst and the Allen-Bradley RSLogix500 PLC platform
• How do I integrate MicroLogix to Catalyst via Modbus TCP/IP using RSLogix 500
• Data samples from the Catalyst log file formatted for use with spreadsheet programs
• SNA = "Source Net Address"
• Preventing Alarmware from updating the Catalyst date/time clock each time I connect
• Where do I find my Catalyst Serial Number?
• Installing 4Mb Memory Expansion Module
• "Status Only" Channels
• Listening to Ambient Noise Near the Catalyst
• Log File Reserve Filled with Data
• PIN Privileges Available
• Bandwidth and Latency Issues with Network Applications
• Procedure for copying a 96 channel unit configuration to a 56 channel unit
• Report precedence
• Power Failure and a Drained Battery
• How do I program my Catalyst to use a digital cell phone?
• Catalyst Logging: Events, Alarms and Phone Calls Monitored
• Adding a Catalyst RTU to Alarmware
• Complete setup report showing all channel setup and alarm points
• LED Front Panel Flashing when the Catalyst is connected to Alarmware
• Catalyst Phone Number Syntax
• ProSoft : User Manuals : Vendor Support for Third Party Communication Modules
• Connecting Catalyst to A-B MicroLogix 1500 Modbus Cable
• Catalyst Modbus Port Bridged to a Modbus Plus Network: MB+ routing fields
• Connecting Catalyst to GE 9030 Modbus Comm. Coprocessor CMM311/CMM711
• Number of devices attached to Modbus Multidrop Cable
• Blind Dialing
• When I order a Catalyst autodialer - what's in the box?
• Configuring a Catalyst Channel to Monitor Data Points and Alarms
• Email Reports Not Delivered
• How to get Catalyst to leave a voice report with voicemail or answering machine
• Catalyst ISP and Email
• Installing Solar Panels for optimal effectiveness
• Catalyst / Verbatim Gateway Ethernet mapping.
• Comport not showing up when startech usb adapter is plugged in
• BICM Module Installation and Operation Catalyst / Verbatim